Sunday, May 14, 2017

Garage workshops part 2

Matt commented on my last post as follows:
I have wall shelves in my garage shop and my tools (and everything else on those shelves) get very dusty. I never thought a tool chest would be a good idea because you have to move so many things to get at the tool you need, which just happens to be at the bottom. Can you comment on your experiences with this?
This is a question many woodworkers considering a tool chest have.  I know I did.  The short answer is that I have not found this to be a problem at all.  A longer answer follows.

My shop is not dusty. I intend to share a video here showing why.  It may make you laugh and perhaps cringe but it works.  Nevertheless, I would not store many of my best tools on shelves.  We have had 54" of rain in the last six months, so rust is a concern.  I think you need a mixture of storage types and there are a lot of items in a garage woodshop that do just fine on shelves, but most tools are not among them.  To store mine, I am an enthusiastic advocate of tool chests.

I originally chose a tool chest over wall cabinets because I knew I was going to be moving and my tools would be in storage.  Another reason was that my garage at the time lacked suitable wall space for cabinets.  I had serious reservations about tool chests, the two most important being about bending over each time I wanted a tool and the same concern about ease of access that Matt has.  Bending over turned out to be a non-issue because the tool chest was approximately six inches off the ground on a dolly I made so I could move the chest around easily.  It's just not a problem, especially because my planes are on the bottom of the chest and they are easy to grasp.  I did eventually make a higher platform to place my chest on, mostly to demonstrate how to overcome that objection.  I keep it because it gives me storage beneath the chest and I don't need mobility, but it is not necessary at all.

Matt's issue concerned me a lot.  I pictured myself constantly sliding tills around to access my tools. I tried to address this by making the tills removable.  I thought I would lift them out and put them on the bench when I was working.  In practice, I never do, because working directly from the chest is so convenient.  I can take just a step or two to access my tools in the chest.  Two tills can be exposed at a time and, in any case they slide easily and quickly on waxed maple rails using three fingers.  It has become second nature and I am no longer even aware that I do it.  I know some woodworkers remove the tools they are going to be using at the beginning of the day and put them on or under their bench on a shelf, but I don't.  It's just as easy to put them away.

Like Matt, I don't want to paw around looking for a tool.  You can minimize this by making shallow tills, making custom holders for your tools that make them easy to access and using the inside of the top.  I made three tills of different depths but, if I had it to do over again, I might make four.  For many of us, tool chests can be quite deep to accommodate them.  My opinion is that you can determine the maximum depth for your tool chest by measuring the distance between your armpit and the second knuckle on your forefinger.  

Tool chests have incredible density.  Usually about 3'x2'x2', they store an amazing amount of tools in just 12 cubic feet.  Their mobility makes them ideal for a small shop and being able to close them quickly when not in use protects the tools from dust and moisture.  You could even easily dehumidy your tool chest if you wanted to.

Here are some pictures that illustrate these points.  Mostly planes on the bottom:


The bottom two tills:


The top till:


All three tills and my saws in place (very secure for travel):


Shop made tools on the lid:



5 comments:

  1. Andy,

    Good looking chest, I like your saw till idea. I have a combination of tool chest, wall shelves, and cabinets but then I no longer live in the PNW. I miss it but.....damn it's nice not to worry about rust.

    ken

    ReplyDelete
  2. Hi Andy
    do you use the draw pins much?

    ReplyDelete
  3. I just got them so I haven't used them yet, but I am certain that I will almost always use them when I make mortises. In the past I have pinned my mortises without drawboring and I really want to start.

    ReplyDelete
  4. That's a great looking kit in that tool chest. Glad it's working out for you and thanks for the extended comments.

    ReplyDelete
  5. Nice kit of tools you got there Andy, very comprehensive. Maybe I should revisit my objections to tool chest storage. But for one thing, i would need a bigger one than my small antique chest :-)

    Bob, catching up on his blogs reading

    ReplyDelete